The fit was perfect on the Rem700, it’s comfortable and looks great, only reason it doesn’t get a Five star yet is because I didn’t get a chance to try it in the cold yet, weather the cap will shrink and come off, the cold in Nunavut will chew up the best of products, I have high hopes tho, everything else I have by MDT holds up in the Arctic

I had a little trouble figuring out I needed to remove the old knob but eventually figured it out. Get lots of positive comments and the green matches the blocks that goes in the butt stock. It feels good in the hand when cycling the action. Would definitely recommend.

Excellent ergonomic, but plastic base of Bolt Knob. My thoughts about this, it will be much better to make of aluminium with different colours. I would pay more for it.

I needed to remove some plastic from the knob - touching the scope - to be able close the bolt completely

The MDT bolt knob fit great on my Remington 700 bolt. Nice tough materials easy installation. I did have to dremel down the inside to fully close on my stock (bell and carlson varmint tactical) however that was easy enough to do and expected. Would highly recommend ANY MDT product.

A perfect size to upgrade your bolt without having to replace your bolt. The added girth looks great and feels even better in you hand. Haha Like everything else MDT builds excellent quality as well.

The bolt knob fit great on my Savage. It made grabbing the action easier and felt smoother to cycle. Plus I believe it looks good.

Good complement to my MDT Tac21 chassis.

Makes for great cycling of the action!

Product was as shown and easy to install. initial lift and after shot feeding with the tikka requires a substantial amount of force to lift the bolt handle. The MDT extension lessens that dramatically and was a 5 star purchase for me.

Purchased two, one for each of my Savage Mk2 rifles. They were a loose fit even with the included black circular pads. I added a strip of doubled sided sticky sponge tape around the bolt knob and several wraps of 1/4” tape to the bolt handle just below the rifle’s bolt knob. Everything was then tight and the MDT bolt knob work perfectly. If the included black pads were three times as thick and sticky on both sides, they would be good without any additional foam or being required.

Great service tracking was right with delivery no complaints

Perfect 👌 👍 🥰 💞 👌

It is great

This was my first purchase from mdt and it won’t be my last. Great product, looks awesome and fast shipping. I didn’t buy the most expensive products but still got a free sample and all around great experience.

To large and soft. Feels mushy.
Expected a much better product from such a capable company known for quality.

Fantastic Quality!!

Fits and works great

Had to drimol out some of the neck channel to get it to fit my howa 1500 sa bolt I have the 24 in heave barrel from brownell not sure if this wus design for a older howa 1500 bolt but didn't close from the box

Says it fits Howa 1500 mini and it in fact does not.

One of the small screws stripped even though I was very careful when installing and had already read the review about someone else experiencing the same problem.

Also, the bolt cannot be fully closed on the original Tikka T3X Lite polymer stock. It does fit perfectly fine on the MDT Oryx chassis.

A bit disappointed with this given the great quality of other products coming from MDT.

Absolutely love the design and everything else. I just recently picked this up from a local dealer when I went to install it. The only issue I had was the two front screws, depending on which one you have. Mine had three one larger one in the back and two smaller screws in the front. Those two smaller screws in the front were just a little too short to fully grab everything and when I went to tighten them all down the front Two completely stripped out all the plastic so I had to custom make two new screws with a little bit thicker thread pitch just to get it to all clap together nicely, but overall absolutely love it. I did happen to put a piece of black electrical tape just around it to thick up When you go to slide the cover on other than that absolutely love it.

ALL OF MDT PRODUCTS ARE TOP KNOTCH GEAR. REALLY WELL MADE AND STLEISH . WORKS AS DESIGNED FLAWLESSLY . PRICED HIGHER THAN SOME BUT VERY WELL BUILT AND WILL LAST A LIFETIME

I bought the bright green bolt knob thinking it was compatible with my Bergera HMR, unfortunately it's not. I also thought based on the images the knob was rubberized, it's just plastic.
- Would be amazing if it could be an "Overmolded" knob instead.

Purchase the MDT knob for my Ruger American. Very clumsy poor fit. Screws too short. The two plastic pieces had to be clamped in order to secure the knob. Once that was done, the cap that goes over it would not stay on. Kept falling off because it was too big. Poor engineering. Don't bother purchasing it won't work. I purchased it from Midway and sent it back. Bad design.

Hello,
I have ordered the bolt knob for my Tikka t3x CTR and Veil Lite. The end of the bolt knob is much bigger than the clamshell from MDT. You guys make great products, just these knobs are too small for what I am assuming is over sized bolt knobs from Tikka?
Either way, the factory bolts don't fit in the MDT knob add on for either of my Tikka's.
A suggestion, you might want to look into this and adjust your website to reflect that it doesn't fit all Tikka bolts?

So that was a waste of money. The two tiny screws stripped out pretty much instantly. If your going to waste your money be careful

I like the size of the knob for my bigger hands

Great idea. The 2 forward screws either are to small in length and/or diameter, or the plastic clam shell is already stripped out.